Bailongju Audi Easy Installation Car Door LED Logo Projector Ghost Shadow Lights 2-pc Set

July 29, 2017 - Comment

Features: 1.Direct replacement.No modifications required.No wire cutting. 2.No error or warning on dashboard. 3.100% Brand New.Never used or tried on 4.Simple installation.Can be done in 5 minutes 5.Cree LED pure white. 6.Voltage:12V with 2000L. Compatibility: Audi A3 (2010 to 2017)A4 (2007 to 2017) A5 (2008 to 2017) A6 (2000 to 2017) A7 (2012 to 2017)

Features:

1.Direct replacement.No modifications required.No wire cutting.
2.No error or warning on dashboard.
3.100% Brand New.Never used or tried on
4.Simple .Can be done in 5 minutes
5.Cree LED pure white.
6.Voltage:12V with 2000L.

Compatibility:

A3 (2010 to 2017)
A4 (2007 to 2017)
A5 (2008 to 2017)
A6 (2000 to 2017)
A7 (2012 to 2017)
A8 (2004 to 2017)
Allroad (2003 to 2017)
Q3 (2013 to 2017)
Q5 (2009 to 2017)
Q7 (2007 to 2017)
R8 (2007 to 2017)
RS4 (2004 to 2017)
RS5 (2004 to 2017)
RS6 (2004 to 2017)
RS7 (2013 to 2017)
S3/S4/S5/S6/S7/S8 (2004 to 2017)
TT/TTS (2008 to 2017)

Package Include:
2 pieces welcome light
Package Size: 9.5 * 3.8 * 9.5 (cm)

Installation Instructions:
1. Use A Flathead Screwdriver Or Installation Tool In The Package To Remove And Disconnect Original Step ;
2. Plug In new Door Lights With Correspondent Connector;
3. Put new Door Lights To The Spot Where Your Original Step Lights Were.
4. Done! Should Be Projecting On To The Ground.

Comments

Mike K. says:

Showing off in Style… Sorry, but I’m a sucker for fun things like this. These are ultra easy in install and look really cool. Very hard to see in the daylight, but that’s OK. At night or in a garage, they light up perfectly. The image is crisp and bright. Not for everyone but for those that want a little extra flair for just a few bucks, this is an easy to add-on that shines in the night. Install time about 3 minutes per door. You just need a small flat head screwdriver and a little electrical tape to seal the connection. Cheers

Hot Tea says:

Pleasantly Surprised. I was impressed. I just bought a “new” 2002 Audi Allroad and wanted to ‘make it mine’ It was really easy to use one of my tiny (#1) flathead screwdrivers to pry out the oem light from the bottom of the door. The wires and connectors are easy to access and Audi provided plenty of slack to work with. Just make sure no wires are pinched between the light and the door when you snap it back in. There were no directions for connecting the main connector nor the jumper wires, but even this blonde figured it out easy enough! It was a tight snap back into position. It will only snap back in the correct position, so if your light ends up reading “IDUA”, you really screwed it up! (just kidding, it wont read backwards…no matter how blonde you are) Anyhow, I had to wait for dark to see the results as I installed it on my concrete drive at high noon in SoCal and couldn’t see a thing. When darkness came, I was not expecting much, and when I opened my driver’s door, I…

Reply to Hot Tea Cancel reply

*